New test method for mechanical strength evaluation of solar cell solder joints

6 СЕНТЯБРЬ 2011

By: R. Klengel*, R. Härtel*, S. Schindler**, D. Schade***, B. Sykes***

Motivation

Fraunhofer IWM, Fraunhofer CSP
Fraunhofer IWM, Fraunhofer CSP

A standardized method with clearly defined good-bad-criteria is not available for testing solder joints that connect single cells into strings. Thus, a comparative characterization of different manufacturers, cell types, base- and joining materials or joining technologies is impossible. The most commonly used test for solar cell ribbon interconnects is the pull test, as used in micro-electronics. For thin, brittle, large area silicon solar cells substantial modifications of the test equipment and methodology are required to realize a suitable metrology. In addition the factors influencing the defect conditions in multi crystalline material, high strains around the solder connect and inhomogeneous contact interfaces has to be considered.

New test method

Requirements to the test method:

  • reproducible (stabile test conditions, no silicon tears, …)
  • comparable (manufacturer, cell types, base- and joining materials, joining technology, …)
  • easy to handle (less handle steps, semi-automatic, little operator influences)
  • high throughput (little setting-up time, high test speed)
  • simply analyzable (statistics, visualization of test values and failure interface)
  • possible correlation to micro structure of solder joints

A XYZTEC Condor 250 multifunctional test machine was upgraded with a new designed test setup. The machine includes a vertical moving z-axis equipped with a force sensor and a x-y-stage for horizontal movement of the work holder. The X-Y table moves the cell at the same velocity than the z-axis pulls the solder ribbon. Thus the point of breakage remains under the measuring head and the test range equates to the ribbon length.

Measurement results XYZTEC Condor 250-3 Solar
Measurement results

Results

The graphical analysis of the measurement results and the images of the fracture interface allow correlating the pull force values with the corresponding failure mode. Every single change in the fracture interface is reproducible in the progression of the curve. So it seems to be possible to conclude to the solder joint condition by interpreting the measured curve.

SAM image of solder joint
SAM image of solder joint
X-ray image of solder joint
X-ray image of solder joint
Cross section of solder joint
Cross section of solder joint
Interface after pull test
Interface after pull test

To correlate the pull test measurement curves and fracture interfaces with concrete interface weakening like voids, non-wetted areas or microcracks etcetera different non-destructive analyzes of soldered bus bar interconnects like scanning acoustic microscopy (SAM) or X-ray inspection with following validation by metallographic cross sections were performed before the pull test.

Summary

With the developed test equipment and measurement routine it is succeeded to provide a reproducible, fast and easy handable method which is usable independent from solar cell geometry, condition of contact materials, soldering technology or manufacturer. It is possible to correlate the measurement curve of the pull test with the fracture interface. This allows to interpret the results with statements in terms of the solder joint quality.


*Fraunhofer Institute for Mechanics of Materials IWM, Walter-Huelse-Strasse 1, 06120 Halle (Saale), Germany Phone +49 (0) 345/5589-159,
** Fraunhofer Center for Silicon Photovoltaics CSP, Walter-Huelse-Strasse 1, 06120 Halle (Saale), Germany
***XYZTEC b.v., J.F.Kennedylaan 14-B, 5981 XC Panningen, The Netherlands

Download as PDF

Click here to download the complete "Mechanical Strength Evaluation of Solar Cell Solder Joints by Developing a New Test Method" as PDF.

Acknowledgement

This work was partly supported by the German Ministry of Economics and Technology under contract “ATSOLOT” (FKZ01FS10010).


Newsletters

ИЮЛ 2019 Meet the world’s biggest bond testers
АПР 2019 Free SMTconnect ticket? Register now
АВГ 2018 Is Fully Automatic Bond Testing Possible?
ИЮЛ 2017 Advances in Thin, 3D and MEMS Die Bond Strength Testing
МАЙ 2017 Shear testing copper pillar
МАР 2017 Fracture strength of thin wafers and die
ФЕВ 2017 Centralized database for enhanced security and SPC options
ЯНВ 2017 Full Automation with Improved Pattern Recognition, Fiducial Marks Analysis, Wire Detect and Failure Mode Analysis
ДЕК 2016 Тестирование покрытий и пленок
НОЯ 2016 Latest software release enables automatic grading
ОКТ 2016 Новые возможности в тестировании материалов
СЕН 2016 Тестирование изделия с крышкой на установке Condor Sigma

 
Click to subscribe.

Other news

03 ОКТ Xyztec at EuWoRel Berlin
18 СЕН Sigma and Magazine Loader in action at Semicon Taiwan
17 СЕН Xyztec at EMPC conference in Pisa
04 СЕН Meet us worldwide in September
05 ИЮЛ Teaming up with Micronnect B.V. and BRIDGE S.r.l.
07 МАЙ Newest Sigma HF High Force bond tester live in action at SMTconnect
26 АПР XYZTEC spreads bond testing knowledge to partners worldwide
20 МАР Visit us at Semicon China
29 ЯНВ XYZTEC at Semicon Korea
21 НОЯ Presentation at CSPT 2018
15 НОЯ Matelec show 2018 for the Electrical and Electronics Industry with Antycip
20 СЕН Successful ESTC Conference in Dresden, Germany
11 ИЮЛ LEGO® for Nepal sponsored by XYZTEC
05 ИЮН Visit us at SMT Hybrid Packaging Nuremberg
20 АПР Smart LED and Solar panels for XYZTEC head office
18 АПР XYZTEC workshop at IMAPS UK
16 МАР ODEOM shows Condor Sigma in Istanbul
15 МАР Semicon China under way
31 ЯНВ Condor Sigma W12 at Semicon Korea
04 ДЕК Condor Sigma stars in Audi Tech Day video
10 НОЯ Raysun to represent XYZTEC in China
23 ОКТ Award for First Technology China
19 ИЮЛ XYZTEC granted subsidy for further accuracy improvements
23 ИЮН Presentation at CSPT 2017 by Bob Sykes
06 ИЮН Condor Sigma in São Paulo, Brazil


View all news

Subscribe to our RSS-feed to be notified of the latest news automatically. You can also find us on Facebook, LinkedIn, Twitter, Weibo 微博, Google+, YouKu 优酷 and YouTube.


XYZTEC Newsletter

Subscribe

Your name:

Your email:


© 1999-2016 XYZTEC BV Disclaimer, Privacy, Cookies

XYZTEC Нидерланды

J.F. Kennedylaan 14-B
5981 XC Panningen
Нидерланды (map / route)

телефон: +31-77-3060920
факс: +31-77-3060919

Find your local representative

XYZTEC Германия

Schäferei 18
06237 Leuna
OT Günthersdorf
Германия
(map / route)
телефон: +49-34638-666690
факс: +49-34638-666695
Cell: +49-172-3272991
Email: Dirk Schade

Совтест АТЕ

Компания Совтест является нашим дистрибьютором на территории России.

Россия, 305000, г. Курск,
ул.Володарского, д.49 а
факс: +7 (4712) 70-88-85
телефон в Курске:
+7 (4712) 73-04-90

Technology leader in bond testing worldwide