Newsletter: Highly reproducible stud pull tests are possible

28 ОКТЯБРЯ 2015

For the modern and complex electronics industry working with surface coatings becomes more and more a basic requirement. 3D MID (Molded Interconnect Device) is based on every conceivable free geometric shape in order to incorporate solutions for robotic fingers or portable electronics in textiles. Glass coatings are used for highly complex multi-layer display solutions to add even more functionality. However, all these components have one thing in common, they need a long service life and be resistant to various environmental influences.

Condor Sigma performing pick and place
Condor Sigma performing pick and place

In order to ensure this, destructive material testing is usually performed. The most well-known are scratch-, stud pull tests. Our September 2015 newsletter described the scratch test. In this newsletter we now describe a practical solution developed by XYZTEC to perform a very reproducible stud pull test. The stud pull test is based on the principle that an adhesive connection is made with the carrier (or object to be tested) by using a glue that is stronger than the bond that needs to be tested.

Two of the biggest challenges are to get an even distribution of the glue and the long curing time associated with some adhesives. If, due to uncontrolled application, the distribution of the glue is not even, menisci are formed that can have a significant influence on the standard deviation and make reproducibility almost impossible. This explains why the stud pull test is only used in limited cases and not during production. The positioning of the studs and the vertical force required to pull the studs also have a negative influence.

Left side detailed view of the Condor Sigma performing pick and place and/or stud pull test
Left side detailed view

The Sigma as a pick and place machine

The solution developed by XYZTEC (in cooperation with other partners) has looked at all these problems and found a solution. The Condor Sigma tester was provided with a micro dispenser that can dispense very small drops of glue (micro liter amounts) very accurately and is cured with UV light. Combined with a USB Tweezer and special tips that look like the inverse of a mushroom, a glass stud can be taken from a magazine fully automatically and placed with a predefined pressure on the surface with the glue. The push force is just sufficient to get a strong connection, without forming any menisci. A special UV light that has been mounted on the machine cures the glue within seconds. The tweezer holds the stud until the test is performed. Before the test the tweezer is positioned in such a way that no unwanted load is applied on the stud, to avoid any influence on the measurement.

Right side detailed view of the Condor Sigma performing pick and place and/or stud pull test
Right side detailed view

Why is holding the tweezer so important?

When the tweezer is released and the operator manually moves the stages, there is a very real risk that the operator due to carelessness bumps into the stud. This applies an unwanted load that can have a significant influence on the test result. With the above method this is nearly impossible. Because UV light cannot be used for all applications XYZTEC also offers different solutions with other studs and glue. Please contact us for more information if this article has aroused your interest, or if you have any questions.

XYZTEC USB Tweezer with special tips for holding glass studs
XYZTEC USB Tweezer with special tips for holding glass studs

Subscribe

Your name:

Your email:


Other newsletters

ИЮЛ 2019 Meet the world’s biggest bond testers
АПР 2019 Free SMTconnect ticket? Register now
АВГ 2018 Is Fully Automatic Bond Testing Possible?
ИЮЛ 2017 Advances in Thin, 3D and MEMS Die Bond Strength Testing
МАЙ 2017 Shear testing copper pillar
МАР 2017 Fracture strength of thin wafers and die
ФЕВ 2017 Centralized database for enhanced security and SPC options
ЯНВ 2017 Full Automation with Improved Pattern Recognition, Fiducial Marks Analysis, Wire Detect and Failure Mode Analysis
ДЕК 2016 Тестирование покрытий и пленок
НОЯ 2016 Latest software release enables automatic grading
ОКТ 2016 Новые возможности в тестировании материалов
СЕН 2016 Тестирование изделия с крышкой на установке Condor Sigma
АВГ 2016 Новый нагреваемый вращающийся рабочий столик для установки Condor Sigma W12 имеет большую рабочую зону
ИЮЛ 2016 How to: Wire Pull
ИЮН 2016 Get 10% off your next tools order
МАЙ 2016 Pull testing bumped wafers
АПР 2016 SMD gull wing leads testing
МАР 2016 Automation: matrix bond testing made easy
ФЕВ 2016 Fully integrated solution for automated wafer testing
ЯНВ 2016 In bond testing, size does matter
ДЕК 2015 XYZTEC goes from strength to strength
НОЯ 2015 Automatic wire detect
ОКТ 2015 Highly reproducible stud pull tests are possible
СЕН 2015 What is the quality of your coatings?
АВГ 2015 Loading samples has never been so easy

Subscribe to our RSS-feed to be notified of the latest news automatically. You can also find us on Facebook, LinkedIn, Twitter, Weibo 微博, Google+, YouKu 优酷 and YouTube.



Bond testing seminars

Aiming to improve understanding of bond testing in the industry, XYZTEC organizes seminars to present and disseminate knowledge in a straightforward format. Click here to find out more about bond testing seminars.


© 1999-2016 XYZTEC BV Disclaimer, Privacy, Cookies

XYZTEC Нидерланды

J.F. Kennedylaan 14-B
5981 XC Panningen
Нидерланды (map / route)

телефон: +31-77-3060920
факс: +31-77-3060919

Find your local representative

XYZTEC Германия

Schäferei 18
06237 Leuna
OT Günthersdorf
Германия
(map / route)
телефон: +49-34638-666690
факс: +49-34638-666695
Cell: +49-172-3272991
Email: Dirk Schade

Совтест АТЕ

Компания Совтест является нашим дистрибьютором на территории России.

Россия, 305000, г. Курск,
ул.Володарского, д.49 а
факс: +7 (4712) 70-88-85
телефон в Курске:
+7 (4712) 73-04-90

Technology leader in bond testing worldwide